![]() However, in the case of a stacked wax rings, top wax ring is forced down on another wax ring that is softer than a toilet flange surface. (c) Top wax ring seal failure – I’d imagine you want a solid “squishing” effect on the top (toilet bowl horn) and the bottom (toilet flange). (B) Bonding failure between the toilet wax rings – with the toilet being slightly wobbly due to uneven tile floor, it is conceivable that the vertical pressure applied on these wax rings are not even, possibly causing gaps in certain spots between wax rings. It would only take a slight bump on the toilet to throw these bolts sideways, possibly damaging the wax ring, creating gaps or even possibly cracking the toilet ceramic. (A) Horizontal racking force on the toilet flange bolts – With approximately 1.5″ space between the flange and the bottom of the toilet, flange bolts are not supported horizontally. After some thinking, I came up with three possible flaws: The entire setup can be purchased under $10 and can be installed with relative ease (although it was a nerve wrecking process for me because you won’t know if the proper seal was made until you flush the toilet).īut in reviewing the double stacked wax ring configuration in detail, I started to wonder if there were some inherent design flaws or weaknesses that attributed to my (sewer gas) situation. It’s a simple configuration of one regular wax ring stacked on top by another “extra thick” wax ring with a built-in flange. Call a reliable plumber and get the problem solved faster.This is probably the most common path taken by DIYers. It is always better to call for a professional expert to get the job done more neatly and appropriately. Let the tank fill up and flush the toilet to check if the replacement has been successful. Turn on the value and restore the water supply. Replace the washers, buts, and plastic caps, and you’re done. Then, set it down gently and use your body weight to add pressure to create a water-tight seal. Lift the toilet from the towel and align it correctly with the holes and bolts. Reinstallation is probably one of the essential aspects. Once this is done, place the new toilet wax ring on top of the flange and install the toilet. While doing so, it’s good practice to replace old bolts with new ones for lasting results. While some corrosion is expected, if the pipe is too degraded, you’ll need to call a professional to replace it. Next, check the flange and look for any cracks or damage. The idea is to get the edges clean and dry to make the new toilet wax ring replacement more effective. Repeat this to the underside of the toilet too. Use a sharp putty knife to break off chunks to hasten the process. Now, you’ll need to scrape off existing wax from the ring. Be sure to distribute the weight evenly across the surface to prevent chipping or damage. Lift the toilet and place it on a lint-free towel. Doing this will loosen the toilet and make it ready to move. Use a screwdriver to remove the bolts holding the toilet to the flange underneath. Pop the lids off the plastic caps encasing the bolts and nuts. Once you’ve got your toilet dry, it’s time to disconnect it. Then, disconnect the plumbing line from the tank. Once this is done, suck out the remaining water using a vacuum or a sponge. For this, remove the water tank’s lid and keep flushing. Next, drain all the water from the toilet. ![]() Note that the toilet’s valve is on the back, and you need to turn the knob clockwise to stop the water. Whether using the toilet’s shutoff valve or restricting water throughout the house, there must be no water in the toilet during the replacement. You must follow these steps and pay attention to instructions to help make this process quick and easy.īefore any replacement, you must turn off the water supply to the toilet. How To Perform A Toilet Wax Ring Replacement?įixing a leaking toilet is not as challenging as it seems. ![]() ![]() Thus, if you’re looking to repair or replace the wax ring, you’ll need to disconnect the toilet from the flooring entirely. It is one of the essential elements of any bathroom to prevent leaks and ensure good hygiene. What Is A Toilet Wax Ring?Ī wax ring creates a water-tight seal around the toilet and the flooring where it meets the drain. If you clear both tests, chances are you’ll need a toilet wax ring replacement. Check for any leaks or drips along the pipe’s body. Once you’ve shut off the main valve to prevent water from flowing through the pipe, inspect the line thoroughly. ![]() First, check the tank, bolts, and gasket where the tank meets the toilet bolt. Are you noticing leaks from the bottom of your toilet? Start by locating the source of the leak. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |